S-2.1, r. 12 - Regulation respecting safety representatives in establishments

Updated to 1 July 2024

This document has official status.

chapter S-2.1, r. 12

Regulation respecting safety representatives in establishments

Act respecting occupational health and safety

(chapter S-2.1, s. 223).

DIVISION I EXCLUSION

1. Chapter V of the Act respecting occupational health and safety (chapter S-2.1), which concerns safety representatives in an establishment, does not apply to establishments with 20 workers or fewer, except for establishments with a health and safety committee established under the second paragraph of section 69 of the Act.

O.C. 1879-84, s. 1.

DIVISION II MINIMUM AMOUNT OF TIME THAT A SAFETY REPRESENTATIVE IN AN ESTABLISHMENT MAY DEVOTE TO EXERCISING SOME OF HIS FUNCTIONS

2. The health and safety committee shall determine the amount of time that one or all of the safety representatives of an establishment may devote to exercising the functions listed in paragraphs 1, 3, 4, 5, 8 and 9 of section 90 of the Act.

Where there is disagreement within the committee or where there is no committee, the time that one or all of the safety representatives of an establishment described in Schedule 1 may devote to those functions is as follows:

(1)  2 hours per week if the establishment has 20 workers or fewer and if a health and safety committee has been established under the second paragraph of section 69 of the Act;

(2)  3 hours per week if the establishment has 21 to 50 workers;

(3)  6 hours per week if the establishment has 51 to 100 workers;

(4)  10 hours per week if the establishment has 100 to 200 workers;

(5)  15 hours per week if the establishment has 201 to 300 workers;

(6)  18 hours per week if the establishment has 301 to 400 workers; or

(7)  21 hours per week if the establishment has 401 to 500 workers.

For establishments with more than 500 workers, 4 hours per week are added for each additional 100 workers.

Where a time allowance prescribed in a collective agreement to one or more workers’ representatives for the purposes of occupational health and safety is equivalent or more advantageous, it is deemed to have been determined by the health and safety committee.

The hours prescribed in the Regulation may not be added to those prescribed in the collective agreement or vice versa.

O.C. 1879-84, s. 2.

3. Where a health and safety committee exists in an establishment, the safety representative is designated from among the workers’ representatives on the health and safety committee.

O.C. 1879-84, s. 3.

DIVISION III REGISTRATION, TRAVEL AND ACCOMMODATION EXPENSES BORNE BY THE COMMISSION

4. The registration, travel and accommodation expenses of a safety representative who participates in a training program whose content and duration are approved by the Commission des normes, de l’équité, de la santé et de la sécurité du travail are borne by the Commission in accordance with the policies that it has established for that purpose.

O.C. 1879-84, s. 4.

DIVISION IV INSTRUMENTS OR APPARATUS THAT A SAFETY REPRESENTATIVE IN AN ESTABLISHMENT NEEDS IN ORDER TO EXERCISE HIS FUNCTIONS

5. The health and safety committee or, if there is no committee, the safety representative and the employer shall determine which instruments and apparatus the safety representative needs to exercise his functions in the establishment.

O.C. 1879-84, s. 5.

6. The health and safety committee or, if there is no committee, the safety representative and the employer shall classify the instruments and apparatus needed by a safety representative to exercise his functions in an establishment into one of the following categories:

(1)  the instruments and apparatus whose availability at all times in the establishment must be ensured by the employer unless he is prevented from doing so for reasons beyond his control; or

(2)  the instruments and apparatus whose availability in the establishment must be ensured by the employer within 48 hours after the safety representative sends a notice to that effect. An employer who cannot follow up the notice within the time allowed must immediately advise the safety representative thereof.

O.C. 1879-84, s. 6.

7. Any disagreement concerning the instruments and apparatus needed by a safety representative to exercise his functions in an establishment or their inclusion in either of the categories in section 6 may be submitted by either party to the Commission, whose decision is executory.

The Commission shall render its decisions on the basis of the list of instruments and apparatus in Schedule 2.

O.C. 1879-84, s. 7.

8. Whenever a safety representative uses an apparatus or instrument necessary for exercising his functions, he shall draft a report addressed to the health and safety committee or, if there is no committee, to the workers or their accredited association and to the employer, containing the following information:

(1)  the time and date of the measurement and the place where it was taken;

(2)  the instruments or apparatus used;

(3)  the duration of the observation;

(4)  the results observed; and

(5)  a description of the environmental conditions prevailing at the work place at the time of the observation specifying, where applicable, to what extent the conditions are exceptional.

The measurement results must be entered in the report immediately after they have been observed.

The report must be drafted as soon as possible, and signed by the safety representative who shall enter therein the time and date of its completion.

O.C. 1879-84, s. 8.

DIVISION V FINAL

9. (Omitted).

O.C. 1879-84, s. 9.

SCHEDULE 1

(s. 2)

GROUP 1

((A) CONSTRUCTION AND PUBLIC WORKS

(1) General contractors

This category includes general construction firms that are primarily engaged in the construction of buildings, highways, or heavy construction such as marine installations, dams, and hydro-electric plants; it excludes establishments that do some construction work but that are primarily engaged in another activity such as utility operation, manufacturing, or mining.

(a) Building construction

General construction firms that are primarily engaged in the construction, alteration and repair of buildings including houses, farm buildings, public buildings, industrial and commercial buildings. This category includes general construction firms that are primarily engaged in speculative building.

(b) Highway, bridge and street construction

General construction firms that are primarily engaged in the construction and repair of highways, grade separations, streets, bridges, viaducts, and airports. This category excludes general construction firms that are primarily engaged in highway or street maintenance, such as tarring, sprinkling, filling potholes and snow removal.

(c) Other construction

General construction firms that are primarily engaged in the construction of such projects as waterworks, gas mains, sewers, hydro-electric plants, transmission lines, telephone lines, power canals, dams, dikes, harbours and canals (including dredging), docks and piers, other marine construction, radio towers, railway right-of-way and structures, and other construction projects not classified elsewhere.

(2) Special-trade contractors

This category includes special-trade construction firms. Special-trade contractors perform only part of the work covered by a contract taken by a general contractor. In all instances, a subcontractor working on part of a project is classified in this category as is jobbing trade work performed directly for owners. Special-trade contractors are often engaged in repair and maintenance work, done at site, on buildings of all types. However, this category excludes maintenance or repair work done by maintenance staffs employed full-time by the establishments on whose premises the work is being done, as well as special-trade construction firms on which they are the sole firm, which are primarily engaged in some other activity such as the fabrication of structural steel parts but which also erect the steel on the sites. Special-trade construction firms classified in this category, include those engaged in bricklaying, carpentry, cement work, electrical work, lathing, plastering, stucco work, painting, decorating, plumbing, heating, air conditioning installations, roofing, terrazo work, steel erection, excavating, flooring, glazing, insulation of buildings, weather stripping, demolition of buildings, water well drilling, sheet metal work, tiling, marble and stone work.

( (B) CHEMICAL AND CHEMICAL PRODUCTS INDUSTRIES

(1) Manufacturers of mixed fertilizers

Establishments primarily engaged in manufacturing mixed fertilizers, including custom mixing. Establishments primarily engaged in manufacturing chemicals such as ammonium nitrate which, in addition to their use as fertilizer materials, also have other important industrial uses, are classified in subparagraph 7.

(2) Manufacturers of plastics and synthetic resins

Establishments primarily engaged in manufacturing synthetic resins in such forms as powders, granules, flakes or liquids, or in compounding synthetic resins into moulding compounds. These establishments may manufacture such products as plastic film and sheet, extrusions and the like from resins of their own manufacture.

Establishments primarily engaged in moulding, extruding and otherwise shaping plastics materials or articles from resins manufactured elsewhere are classified in subparagraph G2. Establishments primarily engaged in manufacturing chemicals for use in making synthetic resins are classified in subparagraph 7. Establishments primarily engaged in the extrusion of synthetic textile filaments are excluded.

(3) Manufacturers of pharmaceuticals and medicines

Establishments primarily engaged in manufacturing drugs and medicines. This category includes manufacturers of patent and proprietary medicines; cod liver oil; and biological product such as antitoxins, bacterins, serums, vaccines; as well as establishments primarily engaged in manufacturing antibiotics and those primarily engaged in grinding drugs and herbs.

(4) Paint and varnish manufacturers

Establishments primarily engaged in manufacturing paints, varnishes, lacquers, enamels and shellac, including establishments primarily engaged in manufacturing products such as putty, filler, oil stain, and thinner.

(5) Manufacturers of soap an cleaning compounds

Establishments primarily engaged in manufacturing soap in any form, synthetic detergents, cleansers, washing powders and cleaning preparations, including scouring powders and hand cleansers. This category includes establishments primarily engaged in manufacturing household laundry bleaches and blueings.

(6) Manufacturers of toilet preparations

Establishments primarily engaged in manufacturing perfumes, cosmetics, lotions, hair dressings, toothpaste and other toilet preparations.

(7) Manufacturers of industrial chemicals

Establishments primarily engaged in manufacturing basic industrial inorganic chemicals such as acids, alkalis, salts, gases under pressure and other inorganic compounds or in manufacturing industrial organic compounds or in manufacturing industrial organic chemicals by chemical processes. This category includes establishments primarily engaged in manufacturing dry colours, pigments, white lead, lead oxides, iron oxides and titanium dioxide and in manufacturing dyes, and establishments primarily engaged in manufacturing synthetic rubber, superphosphates or organic gases under pressure, except petroleum gases.

Establishments primarily engaged in manufacturing coke are classified in subparagraph I1.

Establishments primarily engaged in manufacturing synthetic resins are classified in subparagraph 2; those primarily engaged in manufacturing mixed fertilizers are classified in subparagraph 1. Petroleum refineries are excluded.

(8) Miscellaneous chemical industries

Establishments primarily engaged in manufacturing chemical products not classified elsewhere such as explosives, ammunition, insecticides, germicides, inks, matches, adhesives, polishes and dressings. This category includes establishments primarily engaged in coal tar distillation or wood distillation, and establishments primarily engaged in manufacturing deodorants and disinfectants for household, institutional or industrial use, sweeping compounds and dry cleaning preparations.

((C) FORESTRY AND SAWMILLS

(1) Logging

Establishments primarily engaged in felling and bucking, bunching, yarding, forwarding, decking and loading roundwood, recovering lost logs including sinkers, in transporting wood with specialized logging trucks and in driving, booming, sorting, rafting and towing wood (if not licensed as public carriers), and barking mills engaged in producing barked or rossed pulpwood.

(2) Forestry services

Establishments primarily engaged in forestry patrol, fire inspection, fire fighting, forest nurseries, reforestation and other forestry services, whether conducted by Government organizations or other organizations , excluding forestry consultants.

(3) Sawmills, planing mills and shingle mills

Establishments primarily engaged in sawing lumber (boards, timbers, dimension stock) spoolwood, lath and other mill products such as shingles, cooperage stock and box shook from logs or bolts; and in dressing and working lumber to produce standard matched, shiplapped or patterned products.

Establishments primarily engaged in manufacturing hardwood flooring and millwork products other than lumber are classified in subparagraph F2. Pulp barking mills are classified in subparagraph 1.

( (D) MINES, QUARRIES AND OIL WELLS

(1) Metal mines

(a) Placer gold mines

Establishments primarily engaged in mining gold by placer or hydraulic methods, including establishments primarily engaged in dressing and beneficiating the ore and in producing bullion at the site of the mine.

(b) Gold quartz mines

Establishments primarily engaged in operating lode mines for gold, including establishments primarily engaged in dressing and beneficiating the ore and in producing bullion at the site of the mine.

(c) Uranium mines

Establishments primarily engaged in mining uranium or radium ores and in dressing and beneficiating such ores.

(d) Iron mines

Establishments primarily engaged in mining iron ore and in dressing and beneficiating such ores.

(e) Miscellaneous metal mines

Establishments primarily engaged in mining metal ores not classified elsewhere and in dressing and beneficiating such ores, including the following types of mines: silver, copper-gold-silver, nickel-copper, silver-cobalt, silver-lead-zinc, molybdenite, chromite, manganese, mercury, tungsten, titanium, cerium, rare earths, columbium, tantalum, antimony, magnesium and beryllium.

(2) Mineral fuels

(a) Coal mines

Establishments primarily engaged in mining coal, whether anthracite, bituminous or lignite, including establishments which break, wash, grade or otherwise prepare coal for use as a fuel, whether operated by a coal-mining enterprise or on a contractual basis.

(b) Crude petroleum and natural gas industry

Establishments primarily engaged in the production of petroleum or natural gas from wells or from surface shales or sands, including establishments primarily engaged in recovering the naphtha content of natural gas. The products of these establishments are pentane and heavier liquids, and liquefied petroleum gases, such as butane, propane and butane-propane mixtures; in some cases, elemental sulphur is recovered as a by-products. This category excludes establishments primarily engaged in manufacturing coal gas, when not combined with a blast furnace or chemical plant, and establishments primarily engaged in distributing manufactured or the natural gas to consumers through a system of mains.

(3) Non-metal mines (except coal mines)

(a) Asbestos mines

Establishments primarily engaged in mining and milling asbestos fibre.

(b) Peat extraction

Establishments primarily engaged in recovering and processing peat.

(c) Gypsum mines

Establishments primarily engaged in mining gypsum. Establishments primarily engaged in manufacturing gypsum products and which also mine gypsum are classified in subparagraph J9.

(d) Miscellaneous non-metal mines

Establishments primarily engaged in mining and milling non-metallic minerals not classified elsewhere, including mines such as the following: soapstone and talc, barite, diatomite, mica, ochre and iron oxide, feldspar, nepheline syenite, quartz, silica, fluorspar, salt, potash, sodium sulphate, lithia, magnesite, brucite, gem stones, pumice, volcanic dust, whiting, pozzolana, kyanite, natro-alunite, sodium carbonate, magnesium sulphate, actinolite, serpentine, strontium, graphite, phosphate, pyrite.

(4) Quarries and sand pits

(a) Stone quarries

Establishments primarily engaged in quarrying and crushing igneous rocks (such as granite) or sedimentary rocks (such as limestone, marble, shale, slate and sandstone), excluding establishments primarily engaged in cutting, shaping or finishing stone.

(b) Sand pits or quarries

Establishments primarily engaged in extracting, crushing and screening sand and gravel from pits or quarries.

(5) Services incidental to mining

(a) contract drilling for petroleum

Establishments primarily engaged in the contractual drilling of wells for petroleum or gas, including establishments that specialize in “spudding in” or “drilling in” and in building, repairing and dismantling rigs and derricks.

(b) Other contract drilling

Establishments primarily engaged in contractual diamond drilling.

(c) Miscellaneous services incidental to mining

Establishments primarily engaged in providing services necessary to the operation of petroleum and gas fields, such as running, cutting and pulling casings, tubes and rods; cementing wells; shooting wells; perforating well casings; acidizing and chemically treating wells; cleaning out, bailing, and swabbing wells; and drilling water intake wells. This category also includes establishments primarily engaged in providing services incidental to the operation of metal and non-metal mining, such as mine exploration and development work including the removal of overburden and the sinking of shafts, as well as old style prospecting, but excludes geophysical surveys, gravimetric surveys and seismographic surveys.

( (E) METAL FABRICATING INDUSTRIES

(1) Boiler and plate works

Establishments primarily engaged in manufacturing heating and power boilers, except cast iron sectional heating boilers, heavy gauge storage tanks, pressure tanks, smokestacks, plate work and similar boiler shop products. Cast iron sectional heating boilers are classified in subparagraph 7.

Some establishments in this category are engaged both in the fabrication of the product and its installation. In these cases, the establishment is classified on the basis of its principal activity, i.e. either fabricating or installing the product. Establishments installing mainly products of their own manufacture are considered as primarily engaged in fabrication, and are included in that category, but those primarily engaged in erecting purchased boilers or smokestacks are classified in subparagraph A1c. Establishments primarily engaged in fabricating and erecting large storage tanks which must be assembled at the site are classified in subparagraph 2, and establishments primarily engaged in manufacturing sheet metal tanks are classified in subparagraph 4.

(2) Fabricated structural metal industry

Establishments primarily engaged in fabricating heavy steel parts and similar parts of other metals and alloys for structural purposes. Products in this category include fabricated shapes for bridges, buildings, transmission towers, large tanks and similar structures. Although establishments in this category may erect buildings, bridges, and large tanks as well as fabricate the metal parts thereof, they are primarily engaged in fabrication. Establishments primarily engaged in the erection of buildings, bridges and large tanks from purchased metal parts are excluded.

(3) Ornamental and architectural metal industry

Establishments primarily engaged in manufacturing ornamental metal work, stairs and staircases, fire escapes, grilles, railings, metal windows (including hermetically sealed), doors and frames and metal partitions. Although establishments in this category may install products of their own manufacture, they are primarily engaged in fabrication. Establishments primarily engaged in the erection or installation or purchased fabricated metal products are excluded.

(4) Metal stamping, pressing and coating industry

Establishments primarily engaged in manufacturing sheet metal products such as bottle caps, heel caps, metal lath and metal boxes, including establishments primarily engaged in manufacturing pressed metal products such as kitchen utensils, hospital and similar utensils and containers, establishments primarily engaged in coating metal and metal products, such as vitreous enamelware, galvanizing and electroplating except with precious metals, and establishments primarily engaged in manufacturing tin cans and other tinware, and sheet metal products such as metal awnings, heating ducts, roofing and eaves trough. This category excludes establishments primarily engaged in tinsmithing and sheet metal work on construction projects. Establishments primarily engaged in making enamelled bathroom fixtures such as bath tubs and sinks are classified in subparagraph 9.

(5) Wire and wire products manufacturers

Establishments primarily engaged in drawing wire from rods and in manufacturing nails, spikes, staples, bolts, nuts, rivets, screws, washers, wire fencing, screening, wire cloth, barbed wire, tire chains, uninsulated wire rope and cable, kitchen wire goods and other wire products. This category excludes establishments primarily engaged in manufacturing insulated wire and cable.

(6) Hardware, tool and cutlery manufacturers

Establishments primarily engaged in manufacturing edge and hand tools, cutlery and hardware.

Important products in this category are axes; chisels; dies, including extrusion moulds, and other metal-working tools; hammers, shovels, hoes, rakes, files, saws, builders’ hardware, marine hardware, non-electric razors and blades, table and kitchen cutlery and a miscellaneous group of products usually known under the term «hardware» and not classified elsewhere. This category also includes establishments primarily engaged in manufacturing bits, drills, except rock drill bits, which are excluded, and other cutting tools for machines or for power-driven hand tools. This category excludes establishments primarily engaged in manufacturing sterling silver or silver-plated cutlery, those primarily engaged in manufacturing machine tools or power-driven hand tools, and those primarily engaged in manufacturing machinists’ precision tools.

(7) Heating equipment manufacturers

Establishments primarily engaged in manufacturing commercial cooking equipment and major heating apparatus such as furnaces, oil burners, gas burners, steam and hot water heating apparatus and heating equipment not classified elsewhere. This category includes establishments primarily engaged in manufacturing cast iron sectional heating boilers and convection or cast iron radiators, but excludes establishments primarily engaged in manufacturing electric and non-electric domestic cooking equipment.

(8) Machine shops

Machine shops primarily engaged in producing machine parts and equipment, other than complete machines, for the trade, including machine shops providing custom and repair services, and establishments primarily engaged in rebuilding or remanufacturing automotive engines, transmissions or drives. This category excludes establishments primarily engaged in rebuilding or repairing automotive generators, starter motors and alternators, and establishments primarily engaged in rebuilding such automotive parts as fuel pumps, water pumps, brake shoes, clutches, solenoids and voltage regulators.

(9) Miscellaneous metal fabricating industries

Establishments primarily engaged in manufacturing metal products not classified elsewhere, such as weather stripping, guns, collapsible tubes, machinery fittings, plumbers’ goods (including enamelled plumbing fixtures), safes and vaults, and forgings such as chains (except tire chains, classified in subparagraph 5), anchors and axles; including establishments primarily engaged in fabricating bars and rods for reinforcing concrete and those primarily engaged in metal heat treating.

GROUP 2

((F) WOOD INDUSTRY (excluding sawmills which are classified in subparagraph C-3)

(1) Veneer and plywood mills

Establishments primarily engaged in producing plywood or veneer.

(2) Sash, door and other millwork plants

Establishments primarily engaged in manufacturing mill products such as sash, doors, window and door frames, interior woodwork, mouldings and hardwood flooring. This category also includes establishments primarily engaged in manufacturing prefabricated, wood-framed buildings or prefabricated panels for buildings or in manufacturing laminated beams and structures. Establishments primarily engaged in producing rough, dressed or worked lumber are classified in subparagraph C3. Establishments primarily engaged in producing plywood or veneer are classified in subparagraph 1.

(3) Wooden box factories

Establishments primarily engaged in manufacturing wooden boxes and pallets, crates, fruit and vegetable baskets, including establishments making box shook from sawn lumber.

(4) Coffin and casket industry

Establishments primarily engaged in the manufacture of coffins, caskets and other morticians’ supplies.

(5) Miscellaneous wood industries

Establishments primarily engaged in wood preservation; in wood turning and in manufacturing wood products not elsewhere classified, including sawdust briquettes. Principal products are beekeepers’ and poultrymen’s supplies, excelsior, woodenware (clothespins, washboards, stepladders, pails and tubs), sanitary woodwork and particle board.Establishments primarily engaged in manufacturing cooperage such as barrels, casks, kegs, and other containers made of staves are included in this category.Establishments primarily engaged in manufacturing cooperage stock, but not cooperage, are classified in subparagraph C3.

((G) RUBBER AND PLASTICS PRODUCTS INDUSTRIES

(1) Rubber products industries

Establishments primarily engaged in manufacturing rubber goods, such as rubber tires and tubes for vehicles, machinery and implements; all-rubber footwear, lumbermen’s boots, unlined or flock-lined plastic galoshes, and footwear having fabric uppers and moulded rubber or plastic soles; rubberized fabrics, mechanical rubber goods, rubber flooring and rubber sundries, including establishments primarily engaged in the manufacture of pressure-sensitive tapes including cellulose. Establishments primarily engaged in producing synthetic rubber are classified in subparagraph B7. Establishments primarily engaged in manufacturing rubberized clothing are excluded.

(2) Plastics fabricating industry, n.e.s.

Establishments primarily engaged in using synthetic resins not classified elsewhere and manufactured elsewhere to mold, extrude or otherwise fabricate basic shapes and forms of plastic or plastic articles which cannot conveniently be classified elsewhere, including synthetic sausage casings, plastic bottles and containers, plastic and fibreglass awnings. Many establishments included in this category manufacture special plastic parts for automobiles, household appliances and the like. Establishments primarily engaged in manufacturing plastic articles such as toys, buttons, tooth brushes or any other article for which provision is made elsewhere in the classification should be classified in the appropriate category. Establishments primarily engaged in manufacturing such products as plastic film and sheet, extrusions or the like from resin of their own manufacture are classified in subparagraph B2.

( (H) TRANSPORTATION EQUIPMENT INDUSTRIES

(1) Aircraft and aircraft parts manufacturers

Establishments primarily engaged in manufacturing aeroplanes, gliders, balloons and aircraft parts, such as engines, propellers and pontoons, including aircraft repair and establishments primarily engaged in manufacturing parts for guided missiles and space vehicles. The manufacture of aeronautical instruments, including that of electronic navigational equipment, is excluded. Air-cushioned vehicles are classified in subparagraph 8.

(2) Motor vehicle manufacturers

Establishments primarily engaged in manufacturing or assembling complete motor vehicles such as passenger automobiles, commercial cars and buses, trucks, and special purpose motor vehicles such as ambulances and taxicabs.

(2) Truck body and trailer manufacturers

Establishments primarily engaged in manufacturing truck and bus bodies but not manufacturing complete trucks or buses. Included are establishments primarily engaged in manufacturing truck trailers and tractor-type bus trailers, as well as those primarily engaged in manufacturing trailers for attachment to passenger cars.

(4) Motor vehicle part and accessory manufacturers

Establishments primarily engaged in manufacturing motor vehicle parts, except truck and bus bodies, and accessories for use on motor vehicles, such as engines, brakes, clutches, axles, gears, transmissions, wheels, frames, radiators, springs, automobile hardware, heaters, horns, and mirrors. The manufacture of tires and tubes is classified in subparagraph G1; that of automobile glass, in subparagraph J6; that of automobile fabric accessories and that of batteries are excluded.

(5) Railroad rolling stock industry

Establishments primarily engaged in building and rebuilding locomotives of any type and gauge and railroad cars (including frames and parts) for freight and passenger service.

(6) Shipbuilding and repair

Establishments primarily engaged in building and repairing all types of ships of more than 5 tons displacement.

(7) Boatbuilding and repair

Establishments primarily engaged in building and repairing all types of boats. This industry, for the most part, handles the smaller type of craft, such as motorboats, sailboats, rowboats, lifeboats and canoes.

(8) Miscellaneous vehicle manufacturers

Establishments primarily engaged in manufacturing transportation equipment not elsewhere classified, including snowmobiles, air-cushioned vehicles and animal-drawn vehicles including sleighs, as well as parts for any vehicles included.

( (I) PRIMARY METAL INDUSTRIES

(1) Iron and steel mills

This category includes four main types of establishments:

(1) establishments primarily engaged in manufacturing pig iron and ferroalloys;

(2) 2 steel works primarily engaged in manufacturing lingots, steel castings and in continuous casting of steel;

(3) rolling mills primarily engaged in hot and cold rolling of steel into primary shapes; and

(4) coke ovens operated in connection with blast furnaces. In some cases, the blast furnace, steel mill, rolling mill and coke oven, or some combination of the two or more of them, are carried on as one integrated operation, and the manufacturing processes may be carried on beyond the rolling mill stage.

(2) Steel pipe and tube mills

Establishments primarily engaged in manufacturing welded and seamless steel pipe and tubing. Establishments primarily engaged in manufacturing riveted pipe are classified in subparagraph E2; those primarily engaged in manufacturing cast iron pipe, in subparagraph 3; and those primarily engaged in manufacturing metal culvert pipe, in subparagraph E4.

(3) Iron founderies

Establishments primarily engaged in manufacturing iron castings, including cast iron pipe and fittings.

(4) Smelting and refining

Establishments primarily engaged in the smelting of ores bearing non-ferrous metals and/or the refining of non-ferrous metals. For gold mines, production of bullion at the site of the mine is included with the mining operations in subparagraph D1a or b.

(5) Aluminum rolling, casting and extruding

Establishments primarily engaged in manufacturing aluminum shapes such as bars, rods, plates, sheets and castings or in manufacturing aluminum powder. Pressure die casting of aluminum is classified in subparagraph 7, and the extraction of aluminum from the ore is classified in subparagraph 4.

(6) Copper and copper alloy rolling, casting and extruding

Establishments primarily engaged in manufacturing copper and copper alloy shapes such as bars, rods, plates, sheets and castings or in manufacturing bronze powder. Pressure die casting of copper alloys is classified in subparagraph 7, and the extraction of copper from the ore is classified in subparagraph 4.

(7) Metal rolling, casting and extruding, n.e.s.

Establishments primarily engaged in manufacturing non-ferrous metals such as zinc, tin, lead, nickel and titanium and their alloys in shapes such as bars, rods, plates, sheets and castings, including establishments primarily engaged in pressure die casting of all non-ferrous metals and their alloys and those engaged in the recovery of non-ferrous metals from scrap.

( (J) NON-METALLIC MINERAL PRODUCTS INDUSTRIES

(1) Clay products manufacturers

Establishments primarily engaged in manufacturing clay brick, roofing, floor and wall ceramic tile; sewer pipe, and other structural clay products, including establishments primarily engaged in manufacturing clay products such as pottery, chinaware, and porcelain insulators. Establishments primarily engaged in manufacturing clay refractories are classified in subparagraph 9.

(2) Cement manufacturers

Establishments primarily engaged in manufacturing hydraulic cement, including Portland, natural masonry and pozzolana cements.

(3) Stone products manufacturers

Establishments primarily engaged in cutting, shaping and finishing stone for building and other purposes. Important products of this category include monuments and tombstones, dimension stone for buildings, slate blackboards and stone furniture. Establishments that quarry stone and do some shaping and finishing are classified in subparagraph D4a. Establishments primarily engaged in buying and selling monuments and tombstones are excluded, even though they do some lettering or finishing.

(4) Concrete products manufacturers

Establishments primarily engaged in manufacturing concrete products such as building blocks, brick, sewer pipe, tanks, poles, septic tanks, including establishments primarily engaged in manufacturing sand-lime brick and blocks, but excluding contractors engaged in concrete construction work.

Establishments primarily engaged in mixing and delivering ready-mix concrete are classified in subparagraph 5.

(5) Ready-mix concrete manufacturers

Establishments primarily engaged in mixing and delivering ready-mix concrete.

(6) Glass and glass products manufacturers

Establishments primarily engaged in manufacturing flat glass; plate glass; glass containers; glassware; glass ovenware; glass brick; fibrous glass products except insulation and textile fabrics; mirrors; stained, leaded and ornamental glass; glass novelties and other articles made from glass. This category includes establishments primarily engaged in etching or painting glass or glassware, but excludes establishments primarily engaged in manufacturing optical lenses and ophthalmic lenses. Establishments primarily engaged in spinning glass yarns or weaving glass fabrics are excluded.

(7) Abrasives manufacturers

Establishments primarily engaged in manufacturing abrasive grinding wheels of emery, carborundum and other natural or artificial materials; abrasive sticks, stones, bricks, paper and cloths, and buffing and polishing wheels, including the manufacture of primary abrasive materials such as fused alumina and silicon carbide.

(8) Lime manufacturers

Establishments primarily engaged in manufacturing quicklime and hydrated lime.

(9) Miscellaneous non-metallic mineral products industries

Establishments primarily engaged in manufacturing miscellaneous non-metallic mineral products not classified elsewhere, such as refractories, clay and non-clay gypsum products; mineral wood products; asbestos products; mica products; expanded vermiculite; expanded perlite; roofing granules and dead-burned dolomite. Establishments primarily engaged in manufacturing petroleum and coal products are excluded.

O.C. 1879-84, Sch. 1; O.C. 805-2020, s. 1.

SCHEDULE 2

(s. 7)

LIST OF INSTRUMENTS AND APPARATUS

Tape measure

Combustible gas indicator

Oxygen analyser

Photometer

Smoke tubes and aspirator bulb

Hand pump and detector tubes

Automatique psychrometer

Integrating sound level meter or dosimeter

Laboratory thermometer.

O.C. 1879-84, Sch. 2; O.C. 781-2021, s. 1.

REFERENCES

O.C. 1879-84, 1984 G.O. 2, 3331

S.Q. 2015, c. 15, s. 237

O.C. 805-2020, 2020 G.O. 2, 2007

O.C. 781-2021, 2021 G.O. 2, 1676